Master-Tech Service Center
Seakeeper – Eliminate Boat Roll
As an Authorized Seakeeper installation and service center (the largest Seakeeper dealer in the Northeast) we have the ability to install a Seakeeper on your sport fishing boat, trawler, mega yacht, or commercial vessel. We provide at-your-dock service for Seakeeper regardless of whether we installed it or not. Whether you are located in New Jersey, New York, Connecticut, Rhode Island, Massachusetts, New Hampshire, or Maine, we have the ability to install and service your Seakeeper!
Contact us today to learn more about how a Seakeeper can improve your boating experience or click Here to select a Seakeeper unit for your vessel! Need parts for your Seakeeper? Shop our complete selection of Seakeeper parts.
Seakeeper Units
- Seakeeper 1
- Seakeeper 2
- Seakeeper 3
- Seakeeper 5
- Seakeeper 6
- Seakeeper 9
- Seakeeper 16
- Seakeeper 26
- Seakeeper 35
Seakeeper 1
Regular price $19,900
To bring stabilization to boats as small as 23 feet, we knew we had to break the mold. The new Seakeeper 1 features a flush mount design for easier installation, runs exclusively on 12V DC power, and can be installed virtually anywhere on board.
Innovative Cooling System
Our patented cooling system allows the flywheel to spin at an extremely high rate of speed, providing ultimate performance in the smallest and lightest package possible.
Vacuum Sealed
Seakeeper’s vacuum encapsulation enables the flywheel to spin roughly three times faster, cuts flywheel weight by two-thirds and halves power requirements. Moreover, because the critical components (flywheel, bearings, and motor) are sealed in a vacuum, they are isolated from the marine environment.
Active Control
Seakeeper’s active control optimizes gyro torque, providing an unsurpassed level of performance. Unlike a passively controlled gyro, which must be turned off in the roughest conditions and/or at higher speeds, the Seakeeper is effective at all speeds and can be used in all sea conditions.
Rated Speed | 9,750 RPM |
Angular Momentum at Rated RPM | 1,000 N-M-S |
Max Anti-Rolling Torque at Rated RPM | 2,620 N-M |
Spool-up Time to Rated RPM | 30 minutes (9,750 RPM) |
Spool-up Time to Stabilization | 15 minutes (7,310 RPM) |
Power Consumptions | |
Spool-up Power | 600 Watts Max | Spool-Up Power Input | 12 VDC @ 55 Amps |
Operating Power | 300 – 600 Watts (Sea State Dependent) |
Operating Power Input | 12 VDC @ 25-50 Amps |
Control Power | N/A |
Control Power Input | N/A |
Seawater Pump Power Input, Over Current Protection based on installed pump rating | 12 VDC @ 15 Amps Max |
Weight | 365 lbs (165 kg) Approximately |
Envelope Dimensions | 22.9 L x 23.6 W x 15.7 H (Inches), 0.582 L x 0.598 W x 0.398 H (meters) |
Noise Output | 162-64 dBC at 1 meter |
Seawater Supply to Heat Exchanger | 7.6 LPM (2 GPM) minimum, 15.1 LPM (4 GPM) maximum |
Ambient Air Temperature | 0° – 60° C (32 – 122° F) |
Seakeeper 2
Regular price $19,900
Innovative Cooling System
Our patented cooling system allows the flywheel to spin at an extremely high rate of speed, providing ultimate performance in the smallest and lightest package possible.
Vacuum Sealed
Our patented cooling system allows the flywheel to spin at an extremely high rate of speed, providing ultimate performance in the smallest and lightest package possible.
Active Control
Seakeeper’s vacuum encapsulation enables the flywheel to spin roughly three times faster, cuts flywheel weight by two-thirds and halves power requirements. Moreover, because the critical components (flywheel, bearings, and motor) are sealed for life in a vacuum, they are forever isolated from the marine environment.
Rated Speed | 9,000 RPM |
Angular Momentum at Rated RPM | 2,000 N-M-S |
Max Anti-Rolling Torque at Rated RPM | 5,249 N-M |
Spool-up Time to Rated RPM | 35 minutes (9,000 RPM) |
Spool-up Time to Stabilization | 24 minutes (7,650 RPM) |
Spool-up Power | |
AC Input | N/A |
DC Input | 850 Watts Max |
Operating Power | |
AC Input (sea state dependent) | N/A |
DC Input | 300 – 650 Watts (Sea State Dependent) |
AC Input Voltage (Single Phase) | N/A |
DC Input Voltage | 12 VDC @ 75 Amps |
Weight | 414 lbs (188 kg) |
Envelope Dimensions | 24.8 L x 25.5 W x 20.0 H (inches) 0.630 L x 0.648 W x 0.508 H (meters) |
Noise Output | <68 dBC at 1 meter |
Seakeeper 3
Regular price $27,700
They say great things come in small packages and we set out to prove it. The Seakeeper 3 is our biggest smallest thing yet, specially designed to eliminate roll on ~30’ – 39’ boats. Refits have never been easier than with the Seakeeper 3’s leaning post installation option!
Innovative Cooling System
Our patented cooling system allows the flywheel to spin at an extremely high rate of speed, providing ultimate performance in the smallest and lightest package possible.
Vacuum Sealed
Our patented cooling system allows the flywheel to spin at an extremely high rate of speed, providing ultimate performance in the smallest and lightest package possible.
Active Control
Seakepeeper’s active control optimizes gyro torque, providing an unsurpassed level of performance. Unlike a passively controlled gyro, which must be turned off in the roughest conditions and/or at higher speeds, the Seakeeper is effective at all speeds and can be used in all sea conditions.
Rated Speed | 10,700 RPM |
Angular Momentum at Rated RPM | 5,000 N-M-S |
Anti-Rolling Torque at Rated RPM | 13,089 N-M |
Spool-up Time to Rated RPM | 50 minutes (10,700 RPM) |
Spool-up Time to Stabilization | 35 minutes (9,035 RPM) |
Spool-up Power | |
AC Motor | 2000 Watts Max |
DC Control | 180 Watts |
Operating Power | |
AC Motor (sea state dependent) | 1500 – 2000 Watts |
DC Control | 180 Watts |
AC Input Voltage | 110 – 230 VAC (+/- 10%), 50/60 Hz, Single Phase |
DC Input Voltage | 12 VDC @ 15 Amps |
Weight | 790 lbs (358 kg) |
Envelope Dimensions | 29.7 L x 30.0 W x 24.7 H (inches) 0.755 L x 0.763 W x 0.626 H (meters) |
Noise Output | 70-72 dBC at 1 meter |
Sea Water Supply to Heat Exchanger | 30 LPM (8 GPM) maximum 15 LPM (4 GPM) minimum |
Ambient Air Temperature | 0° – 60° C (32° – 140° F) |
(Seakeeper 5 also comes in a DC version, the SK 3DC – Contact Seakepeer for specs) |
Seakeeper 5
Regular price $38,900
Small, but powerful. We pushed performance engineering to all new levels to create a small, efficient gyro. The Seakeeper 5 is designed to eliminate up to 95% of boat roll on ~40’ – 49’ boats, up to ~20 tons.
Innovative Cooling System
Our patented cooling system allows the flywheel to spin at an extremely high rate of speed, providing ultimate performance in the smallest and lightest package possible.
Vacuum Sealed
Seakeeper’s vacuum encapsulation enables the flywheel to spin roughly three times faster, cuts flywheel weight by two-thirds and halves power requirements. Moreover, because the critical components (flywheel, bearings, and motor) are sealed for life in a vacuum, they are forever isolated from the marine environment.
Active Control
Seakepeeper’s active control optimizes gyro torque, providing an unsurpassed level of performance. Unlike a passively controlled gyro, which must be turned off in the roughest conditions and/or at higher speeds, the Seakeeper is effective at all speeds and can be used in all sea conditions.
Rated Speed | 10,700 RPM |
Angular Momentum at Rated RPM | 5,000 N-M-S |
Anti-Rolling Torque at Rated RPM | 13,089 N-M |
Spool-up Time to Rated RPM | 50 minutes (10,700 RPM) |
Spool-up Time to Stabilization | 35 minutes (9,035 RPM) |
Spool-up Power | |
AC Motor | 2000 Watts Max |
DC Control | 180 Watts |
Operating Power | |
AC Motor (sea state dependent) | 1500 – 2000 Watts |
DC Control | 180 Watts |
AC Input Voltage | 110 – 230 VAC (+/- 10%), 50/60 Hz, Single Phase |
DC Input Voltage | 12 VDC @ 15 Amps |
Weight | 790 lbs (358 kg) |
Envelope Dimensions | 29.7 L x 30.0 W x 24.7 H (inches) 0.755 L x 0.763 W x 0.626 H (meters) |
Noise Output | 70-72 dBC at 1 meter |
Sea Water Supply to Heat Exchanger | 30 LPM (8 GPM) maximum 15 LPM (4 GPM) minimum |
Ambient Air Temperature | 0° – 60° C (32° – 140° F) |
(Seakeeper 5 also comes in a DC version, the SK 3DC – Contact Seakepeer for specs) |
Seakeeper 6
Regular price $45,900
The Seakeeper 6 packs a punch. Designed toeliminate up to 95% of boat roll on boats up
to ~20 tons, vessels ~40 – 49’, the Seakeeper 6provides 6,000 N-M-S of stabilizing power in a compact, efficient package.
Innovative Cooling System
Our patented cooling system allows the flywheel to spin at an extremely high rate of speed, providing ultimate performance in the smallest and lightest package possible.
Vacuum Sealed
Seakeeper’s vacuum encapsulation enables the flywheel to spin roughly three times faster, cuts flywheel weight by two-thirds and halves power requirements. Moreover, because the critical components (flywheel, bearings, and motor) are sealed for life in a vacuum, they are forever isolated from the marine environment.
Active Control
Seakepeeper’s active control optimizes gyro torque, providing an unsurpassed level of performance. Unlike a passively controlled gyro, which must be turned off in the roughest conditions and/or at higher speeds, the Seakeeper is effective at all speeds and can be used in all sea conditions.
Rated Speed | 9,700 RPM |
Angular Momentum at Rated RPM | 6,000 N-M-S |
Anti-Rolling Torque at Rated RPM | 15,690 N-M |
Spool-up Time to Rated RPM | 40 minutes (9,700 RPM) |
Spool-up Time to Stabilization | 24 minutes (7,700 RPM) |
Spool-up Power | |
AC Motor | 2300 Watts |
DC Control | 125 Watts |
Operating Power | |
AC Motor (sea state dependent) | 1050 – 2300 Watts |
DC Control | 125 Watts |
AC Input Voltage | 110 – 230 VAC (+/- 10%), 50/60 Hz, Single Phase |
DC Input Voltage | 12 VDC @ 15 Amps |
Weight | 395 kg (870 lbs) |
Envelope Dimensions | Length x Width x Height 0.756 L x 0.755 W x 0.626 H (meters) 29.77 L x 29.71 W x 24.65 H (inches) |
Noise Output | 70-72 dBC at 1 meter |
Sea Water Supply to Heat Exchanger | 30 LPM (8 GPM) maximum 15 LPM (4 GPM) minimum |
Ambient Air Temperature | 0° – 60° C (32° – 140° F) |
Seakeeper 9
Regular price $77,900
An evolution of our original M7000, the Seakeeper 9 is the product that changed the boating experience forever! Specially designed to stabilize boats ~50’ – 59’, or up to ~30 tons..
Innovative Cooling System
Our patented cooling system allows the flywheel to spin at an extremely high rate of speed, providing ultimate performance in the smallest and lightest package possible.
Vacuum Sealed
Seakeeper’s vacuum encapsulation enables the flywheel to spin roughly three times faster, cuts flywheel weight by two-thirds and halves power requirements. Moreover, because the critical components (flywheel, bearings, and motor) are sealed for life in a vacuum, they are forever isolated from the marine environment.
Active Control
Seakepeeper’s active control optimizes gyro torque, providing an unsurpassed level of performance. Unlike a passively controlled gyro, which must be turned off in the roughest conditions and/or at higher speeds, the Seakeeper is effective at all speeds and can be used in all sea conditions.
Rated Speed | 9,000 RPM |
Angular Momentum at Rated RPM | 9,000 N-M-S |
Anti-Rolling Torque at Rated RPM | 18,810 N-M |
Spool-up Time to Rated RPM | 55 minutes (9,000 RPM) |
Spool-up Time to Stabilization | 38 minutes (7,650 RPM) |
Spool-up Power | |
AC Motor | 3000 Watts Max |
DC Control | 240 Watts |
Operating Power | |
AC Motor (sea state dependent) | 1500 – 2000 Watts |
DC Control | 240 Watts |
AC Input Voltage | 208 – 230 VAC (+/- 10%), 50/60 Hz, Single Phase |
DC Input Voltage | 24 VDC @ 10 Amps |
Weight | 1,210 lbs (550 kg) |
Envelope Dimensions | 33.5 L x 35.6 W x 28.3 H (inches) 0.852 L x 0.903 W x 0.720 H (meters) |
Noise Output | 68-70 dBC at 1 meter |
Sea Water Supply to Heat Exchanger | 30 LPM (8 GPM) maximum 15 LPM (4 GPM) minimum |
Ambient Air Temperature | 0°-60° C (32° – 140° F) |
Seakeeper 16
Regular price $109,900
Crafted for ~60’ – 69’ boats, up to ~50 tons, the Seakeeper 16 is designed to eliminate up to
95% of boat roll. The Seakeeper 16 is completely internal, requires only modest electrical power, and can be installed virtually anywhere on board.
Innovative Cooling System
Our patented cooling system allows the flywheel to spin at an extremely high rate of speed, providing ultimate performance in the smallest and lightest package possible.
Vacuum Sealed
Seakeeper’s vacuum encapsulation enables the flywheel to spin roughly three times faster, cuts flywheel weight by two-thirds and halves power requirements. Moreover, because the critical components (flywheel, bearings, and motor) are sealed for life in a vacuum, they are forever isolated from the marine environment.
Active Control
Seakepeeper’s active control optimizes gyro torque, providing an unsurpassed level of performance. Unlike a passively controlled gyro, which must be turned off in the roughest conditions and/or at higher speeds, the Seakeeper is effective at all speeds and can be used in all sea conditions.
Rated Speed | 6,130 RPM |
Angular Momentum at Rated RPM | 16,000 N-M-S |
Anti-Rolling Torque at Rated RPM | 30,720 N-M |
Spool-up Time to Rated RPM | 57 minutes (6,130 RPM) |
Spool-up Time to Stabilization | 45 minutes (5,210 RPM) |
Spool-up Power | |
AC Motor | 3000 Watts Max |
DC Control | 240 Watts |
Operating Power | |
AC Motor (sea state dependent) | 2300 – 3000 Watts |
DC Control | 240 Watts |
AC Input Voltage | 208 – 230 VAC (+/- 10%), 50/60 Hz, Single Phase |
DC Input Voltage | 24 VDC @ 10 Amps |
Weight | 2,195 lbs (996 kg) |
Envelope Dimensions | 42.6 L x 43.2 W x 32.8 H (inches) 1.08 L x 1.10 W x 0.83 H (meters) |
Noise Output | 68-73 dBC at 1 meter |
Sea Water Supply to Gyro Heat Exchanger | 30 LPM (8 GPM) maximum 15 LPM (4 GPM) minimum |
Ambient Air Temperature | 0°-60° C (32°-140° F) |
Seakeeper 26
Regular price $166,900
Designed to eliminate up to 95% of boat roll, the Seakeeper 26 is sized for vessels ~70′ – 84’, up to ~75 tons. Unlike traditional external fins, the Seakeeper 26 has no outside appendages, requires only modest electrical power, and can be installed virtually anywhere on board.
Innovative Cooling System
Our patented cooling system allows the flywheel to spin at an extremely high rate of speed, providing ultimate performance in the smallest and lightest package possible.
Vacuum Sealed
Seakeeper’s vacuum encapsulation enables the flywheel to spin roughly three times faster, cuts flywheel weight by two-thirds and halves power requirements. Moreover, because the critical components (flywheel, bearings, and motor) are sealed for life in a vacuum, they are forever isolated from the marine environment.
Active Control
Seakepeeper’s active control optimizes gyro torque, providing an unsurpassed level of performance. Unlike a passively controlled gyro, which must be turned off in the roughest conditions and/or at higher speeds, the Seakeeper is effective at all speeds and can be used in all sea conditions.
Rated Speed | 5,000 RPM |
Angular Momentum at Rated RPM | 26,000 N-M-S |
Anti-Rolling Torque at Rated RPM | 56,000 N-M |
Spool-up Time to Rated RPM | 90 minutes (5,000 RPM) |
Spool-up Time to Stabilization | 70 minutes (4,250 RPM) |
Spool-up Power | |
AC Motor | 3000 Watts Max |
DC Control | 240 Watts |
Operating Power | |
AC Motor (sea state dependent) | 1000 – 3000 Watts |
DC Control | 240 Watts |
AC Input Voltage | 208 – 230 VAC (+/- 10%), 50/60 Hz, Single Phase |
DC Input Voltage | 24 VDC @ 10 Amps |
Weight | 2,960 lbs (1,342 kg) |
Envelope Dimensions | 52.7 L x 55.9 W x 40.4 H (inches) 1.34 L x 1.42 W x 1.03 H (meters) |
Noise Output | 72-74 dBC at 1 meter |
Sea Water Supply to Heat Exchanger | 30 LPM (8 GPM) maximum 15 LPM (4 GPM) minimum |
Ambient Air Temperature | 0° – 60° C (32° – 140° F) |
Seakeeper 35
Regular price $216,300
The Seakeeper 35 is designed to eliminate up to 95% of boat roll on boats up to ~100 tons, vessels ~85′ and larger. Multiple units can be fitted for larger boats. Unlike traditional external fins, the Seakeeper 35 requires only modest electrical power, has no external appendages— meaning no drag or risk of snags—and can be installed virtually anywhere on board.
Innovative Cooling System
Our patented cooling system allows the flywheel to spin at an extremely high rate of speed, providing ultimate performance in the smallest and lightest package possible.
Vacuum Sealed
Seakeeper’s vacuum encapsulation enables the flywheel to spin roughly three times faster, cuts flywheel weight by two-thirds and halves power requirements. Moreover, because the critical components (flywheel, bearings, and motor) are sealed for life in a vacuum, they are forever isolated from the marine environment.
Active Control
Seakepeeper’s active control optimizes gyro torque, providing an unsurpassed level of performance. Unlike a passively controlled gyro, which must be turned off in the roughest conditions and/or at higher speeds, the Seakeeper is effective at all speeds and can be used in all sea conditions.
Rated Speed | 5,150 RPM |
Angular Momentum at Rated RPM | 35,000 N-M-S |
Anti-Rolling Torque at Rated RPM | 73,000 N-M |
Spool-up Time to Rated RPM | 65 minutes (5,150 RPM) |
Spool-up Time to Stabilization | 45 minutes (4,380 RPM) |
Spool-up Power | |
AC Motor | 5000 Watts Max |
DC Control | 240 Watts |
Operating Power | |
AC Motor (sea state dependent) | 2000 – 5000 Watts |
DC Control | 240 Watts |
AC Input Voltage | 208 – 230 VAC (+/- 10%), 50/60 Hz, Single Phase |
DC Input Voltage | 24 VDC @ 10 Amps |
Weight | 3,920 lbs (1,778 kg) |
Envelope Dimensions | 54.3 L x 55.9 W x 43.5 H (inches) 1.38 L x 1.42 W x 1.11 H (meters) |
Noise Output | 72-74 dBC at 1 meter |
Sea Water Supply to Heat Exchanger | 53.0 LPM (14 GPM) maximum 38.0 LPM (10 GPM) minimum |
Ambient Air Temperature | 0° – 60° C (32° – 140° F) |
Seakeeper 7HD
Regular price $77,900
COMMERCIAL GRADE STABILIZATION
Designed to eliminate up to 95% of boat roll on ~45’ – 54’ vessels, up to ~25 tons, the Seakeeper 7HD is completely internal, requires only modest electrical power, and can be installed virtually anywhere on board.
Innovative Cooling System
Our patented cooling system allows the flywheel to spin at an extremely high rate of speed, providing ultimate performance in the smallest and lightest package possible.
Vacuum Sealed
Seakeeper’s vacuum encapsulation enables the flywheel to spin roughly three times faster, cuts flywheel weight by two-thirds and halves power requirements. Moreover, because the critical components (flywheel, bearings, and motor) are sealed for life in a vacuum, they are forever isolated from the marine environment.
Active Control
Seakepeeper’s active control optimizes gyro torque, providing an unsurpassed level of performance. Unlike a passively controlled gyro, which must be turned off in the roughest conditions and/or at higher speeds, the Seakeeper is effective at all speeds and can be used in all sea conditions.
Rated Speed | 7,000 RPM |
Angular Momentum at Rated RPM | 7,000 N-M-S |
Anti-Rolling Torque at Rated RPM | 14,630 N-M |
Spool-up Time to Rated RPM | 35 minutes (7,000 RPM) |
Spool-up Time to Stabilization | 25 minutes (5,600 RPM) |
Spool-up Power | |
AC Motor | 3000 Watts Max |
DC Control | 240 Watts |
Operating Power | |
AC Motor (sea state dependent) | 1000 – 2000 Watts |
DC Control | 240 Watts |
AC Input Voltage | 208 – 230 VAC (+/- 10%), 50/60 Hz, Single Phase |
DC Input Voltage | 24 VDC @ 10 Amps |
Weight | 1,210 lbs (550 kg) |
Envelope Dimensions | 33.5 L x 35.6 W x 28.3 H (inches) 0.852 L x 0.903 W x 0.720 H (meters) |
Noise Output | 68-70 dBC at 1 meter |
Seakeeper 12HD
Regular price $109,900
COMMERCIAL GRADE STABILIZATION
Optimized for ~55’ – 64’ boats, up to ~35 tons, the Seakeeper 12HD is designed to eliminate up to 95% of boat roll. Our gyros are completely internal, require only modest electrical power, and can be installed virtually anywhere on board.
Innovative Cooling System
Our patented cooling system allows the flywheel to spin at an extremely high rate of speed, providing ultimate performance in the smallest and lightest package possible.
Vacuum Sealed
Seakeeper’s vacuum encapsulation enables the flywheel to spin roughly three times faster, cuts flywheel weight by two-thirds and halves power requirements. Moreover, because the critical components (flywheel, bearings, and motor) are sealed for life in a vacuum, they are forever isolated from the marine environment.
Active Control
Seakepeeper’s active control optimizes gyro torque, providing an unsurpassed level of performance. Unlike a passively controlled gyro, which must be turned off in the roughest conditions and/or at higher speeds, the Seakeeper is effective at all speeds and can be used in all sea conditions.
Rated Speed | 4,600 RPM |
Angular Momentum at Rated RPM | 12,000 N-M-S |
Anti-Rolling Torque at Rated RPM | 23,040 N-M |
Spool-up Time to Rated RPM | 45 minutes (4,600 RPM) |
Spool-up Time to Stabilization | 35 minutes (3,680 RPM) |
Spool-up Power | |
AC Motor | 3000 Watts Max |
DC Control | 240 Watts |
Operating Power | |
AC Motor (sea state dependent) | 1000 – 3000 Watts |
DC Control | 240 Watts |
AC Input Voltage | 208 – 230 VAC (+/- 10%), 50/60 Hz, Single Phase |
DC Input Voltage | 24 VDC @ 10 Amps |
Weight | 2,195 lbs (996 kg) |
Envelope Dimensions | 42.6 L x 43.2 W x 32.8 H (inches) 1.08 L x 1.10 W x 0.83 H (meters) |
Noise Output | 68-73 dBC at 1 meter |
Seakeeper 20HD
Regular price $166,900
COMMERCIAL GRADE STABILIZATION
The Seakeeper 20HD is optimized to eliminate up to 95% of boat roll on boats ~65 – 74 feet, up to ~60 tons. Unlike traditional external fins, the Seakeeper 20HD requires only modest electrical power and has no external appendages, and can be installed virtually anywhere on board.
Innovative Cooling System
Our patented cooling system allows the flywheel to spin at an extremely high rate of speed, providing ultimate performance in the smallest and lightest package possible.
Vacuum Sealed
Seakeeper’s vacuum encapsulation enables the flywheel to spin roughly three times faster, cuts flywheel weight by two-thirds and halves power requirements. Moreover, because the critical components (flywheel, bearings, and motor) are sealed for life in a vacuum, they are forever isolated from the marine environment..
Active Control
Seakepeeper’s active control optimizes gyro torque, providing an unsurpassed level of performance. Unlike a passively controlled gyro, which must be turned off in the roughest conditions and/or at higher speeds, the Seakeeper is effective at all speeds and can be used in all sea conditions.
Rated Speed | 3,850 RPM |
Angular Momentum at Rated RPM | 20,000 N-M-S |
Anti-Rolling Torque at Rated RPM | 43,076 N-M |
Spool-up Time to Rated RPM | 70 minutes (3,850 RPM) |
Spool-up Time to Stabilization | 50 minutes (3,100 RPM) |
Spool-up Power | |
AC Motor | 3000 Watts Max |
DC Control | 240 Watts |
Operating Power | |
AC Motor (sea state dependent) | 1000 – 3000 Watts |
DC Control | 240 Watts |
AC Input Voltage | 208 – 230 VAC (+/- 10%), 50/60 Hz, Single Phase |
DC Input Voltage | 24 VDC @ 10 Amps |
Weight | 2,960 lbs (1,342 kg) |
Envelope Dimensions | 52.7 L x 55.9 W x 40.4 H (inches) 1.34 L x 1.42 W x 1.03 H (meters) |
Noise Output | 72-74 dBC at 1 meter |
Seakeeper 30HD
Regular price $216,300
COMMERCIAL GRADE STABILIZATION
The Seakeeper 30HD is built to eliminate up to 95% of boat roll on vessels up to ~85 tons. Larger vessels can be fitted with multiple units to achieve optimal results. Unlike traditional external fins, the Seakeeper 30HD requires only modest electrical power and has no external appendages—meaning no drag or risk of snags.
Innovative Cooling System
Our patented cooling system allows the flywheel to spin at an extremely high rate of speed, providing ultimate performance in the smallest and lightest package possible.
Vacuum Sealed
Seakeeper’s vacuum encapsulation enables the flywheel to spin roughly three times faster, cuts flywheel weight by two-thirds and halves power requirements. Moreover, because the critical components (flywheel, bearings, and motor) are sealed for life in a vacuum, they are forever isolated from the marine environment.
Active Control
Seakepeeper’s active control optimizes gyro torque, providing an unsurpassed level of performance. Unlike a passively controlled gyro, which must be turned off in the roughest conditions and/or at higher speeds, the Seakeeper is effective at all speeds and can be used in all sea conditions.
Rated Speed | 4,400 RPM |
Angular Momentum at Rated RPM | 30,000 N-M-S |
Anti-Rolling Torque at Rated RPM | 62,571 N-M |
Spool-up Time to Rated RPM | 75 minutes (4,400 RPM) |
Spool-up Time to Stabilization | 50 minutes (3,500 RPM) |
Spool-up Power | |
AC Motor | 3000 Watts Max |
DC Control | 240 Watts |
Operating Power | |
AC Motor (sea state dependent) | 2000 – 3000 Watts |
DC Control | 240 Watts |
AC Input Voltage | 208 – 230 VAC (+/- 10%), 50/60 Hz, Single Phase |
DC Input Voltage | 24 VDC @ 10 Amps |
Weight | 3,920 lbs (1,778 kg) |
Envelope Dimensions | 54.3 L x 55.9 W x 43.5 H (inches) 1.38 L x 1.42 W x 1.11 H (meters) |
Noise Output | 72-74 dBC at 1 meter |
Parts Sales
Recent Work